Rigid Foam Board Insulation in Wedgefield, Florida
EPS, XPS and polyiso boards for continuous insulation, roofing, foundations and thermal-bridge-free assemblies.
Rigid Foam Board Insulation for Wedgefield Properties
Rigid foam boards deliver the highest R-value per inch of any non-spray product and, more importantly, install as a continuous layer. Continuity is the point: an unbroken sheet of foam outside the framing removes the thermal short-circuit that studs create in every insulated wall.
In Orange County generally, and Wedgefield specifically, this comes up most often on properties where the existing assembly has stopped performing and a straightforward top-up will not solve the underlying problem.
Wedgefield sits in Orange County, climate zone 2A, where the recommended attic target is R-49 to R-60. That number, along with where your ductwork runs and what condition the existing assembly is in, is what determines the right specification for your property.
Rigid Foam Board Insulation at a glance
R-value: R-3.8 per inch (EPS) / R-5.0 per inch (XPS) / R-5.6 to R-6.5 per inch (polyiso)
Installed cost: $1.40 – $3.80 per square foot installed
Service life: 50+ years
Available in: Wedgefield and throughout Orange County
Types and Methods
EPS — expanded polystyrene
The most affordable and the most vapor-permeable of the three. Stable long-term R-value, common under slabs and in insulated concrete forms.
XPS — extruded polystyrene
The familiar pink or blue board. Higher compressive strength and very low water absorption, which makes it the standard for below-grade and under-slab work.
Polyiso — polyisocyanurate
The highest R-value per inch and the dominant material on commercial low-slope roofs. Foil facers add a radiant benefit. Note that polyiso's R-value drops somewhat at low temperatures — largely a non-issue in Florida.
Board layout matters as much as board R-value. Unstaggered seams, missing tape and poor flashing integration will undo the performance you paid for. On commercial roofing we coordinate directly with the roofing contractor so the insulation and membrane systems work as one.
Benefits for Wedgefield Property Owners
- Highest R-value per inch available in board form
- Continuous coverage eliminates framing thermal bridges
- Adds structural rigidity and racking resistance to the assembly
- Moisture-resistant and dimensionally stable over decades
- Doubles as an air barrier when seams are properly taped
- Available in fire-rated and foil-faced configurations
Best Applications
- Low-slope commercial roofs
- Continuous exterior wall insulation
- Under concrete slabs
- Foundation and stem walls
- Cathedral and vaulted ceilings
How We Install It in Wedgefield
- Assembly review, including dew-point analysis for the specific wall
- Board type, thickness and facer selected for the application
- Substrate prep and confirmation that the surface is flat and dry
- Boards cut and staggered so seams do not align between layers
- Mechanical fastening with correct plate density and pattern
- All seams taped and sealed to form a continuous air control layer
- Flashing integration at windows, doors and terminations
Cost and R-Value Reference
| Material | Installed cost | R-value per inch | Service life |
|---|---|---|---|
| Blown-in fiberglass | $1.10 – $2.00 / sq ft | R-3.2 – R-3.8 | 20–30 years |
| Blown-in cellulose | $1.20 – $2.40 / sq ft | R-3.2 – R-3.8 | 20–30 years |
| Fiberglass batts | $0.90 – $2.10 / sq ft | R-3.1 – R-4.3 | 25+ years |
| Mineral wool | $1.60 – $3.40 / sq ft | R-3.0 – R-4.3 | 50+ years |
| Open-cell spray foam | $1.50 – $3.20 / sq ft | R-3.6 – R-3.8 | 80+ years |
| Closed-cell spray foam | $2.40 – $4.90 / sq ft | R-6.0 – R-7.0 | 80+ years |
| Rigid foam board | $1.40 – $3.80 / sq ft | R-3.8 – R-6.5 | 50+ years |
| Radiant barrier | $0.55 – $1.90 / sq ft | Reflective (no R) | 25+ years |
| Insulation removal | $1.10 – $2.90 / sq ft | — | One-time |
Pricing reflects typical Florida installed costs and varies with access, square footage and site conditions.
Rigid Foam Board Insulation FAQs — Wedgefield
How much does rigid foam board insulation cost in Wedgefield?
Typical installed pricing in Wedgefield runs $1.40 – $3.80 per square foot installed. Final cost depends on square footage, access, target R-value and whether existing material has to be removed first. Every quote itemizes material, R-value, installed inches and square footage.
What R-value will I get?
R-3.8 per inch (EPS) / R-5.0 per inch (XPS) / R-5.6 to R-6.5 per inch (polyiso). Wedgefield is in climate zone 2A, where the attic target is R-49 to R-60, so installed depth is calculated from that target.
How long does it last?
50+ years.
How soon can you start in Wedgefield?
Inspections typically within two to four business days, installation within one to two weeks. Emergency storm work is prioritized ahead of scheduled projects.
Other Services in Wedgefield
- Spray Foam Insulation in Wedgefield
- Blown-In Insulation in Wedgefield
- Fiberglass Batt Insulation in Wedgefield
- Attic Insulation in Wedgefield
- Radiant Barrier Insulation in Wedgefield
- Insulation Removal in Wedgefield
- Crawl Space Insulation in Wedgefield
- Wall Insulation in Wedgefield
- Mineral Wool Insulation in Wedgefield
- Duct Insulation and Sealing in Wedgefield
- Air Sealing in Wedgefield
- Soundproofing Insulation in Wedgefield
- Metal Building Insulation in Wedgefield
Rigid Foam Board Insulation Nearby
- Orlando
- Apopka
- Winter Garden
- Ocoee
- Winter Park
- Maitland
- Oakland
- Eatonville
- Edgewood
- Belle Isle
- Windermere
- Bay Lake
- Lake Buena Vista
- Winter Springs
- Pine Hills
- Doctor Phillips
- Hunters Creek
- Meadow Woods
- Azalea Park
- Conway
- Fairview Shores
- Goldenrod
- Horizon West
- Lockhart
- Union Park
- Alafaya
All of Orange County →
Statewide Rigid Foam Board Insulation page →
Rigid Foam Board Insulation Estimates in Wedgefield, FL
Free attic inspection, photographs of what we find, and a written scope with material, R-value, inches and square footage. No obligation.